View MMSF3350-D_896327.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MMSF3350 WaveFETTM HDTMOSTM Single N-Channel Field Effect Transistor
Power Surface Mount Products
http://onsemi.com
WaveFET devices are an advanced series of power MOSFETs which utilize ON Semiconductor's latest MOSFET technology process to achieve the lowest possible on-resistance per silicon area. They are capable of withstanding high energy in the avalanche and commutation modes and the drain-to-source diode has a very low reverse recovery time. WaveFET devices are designed for use in low voltage, high speed switching applications where power efficiency is important. Typical applications are dc-dc converters, and power management in portable and battery powered products such as computers, printers, cellular and cordless phones. They can also be used for low voltage motor controls in mass storage products such as disk drives and tape drives. The avalanche energy is specified to eliminate the guesswork in designs where inductive loads are switched and offer additional safety margin against unexpected voltage transients. * Characterized Over a Wide Range of Power Ratings * Ultralow RDS(on) Provides Higher Efficiency and Extends Battery Life in Portable Applications * Logic Level Gate Drive - Can Be Driven by Logic ICs * Diode Is Characterized for Use In Bridge Circuits * Diode Exhibits High Speed, With Soft Recovery * IDSS Specified at Elevated Temperature * Avalanche Energy Specified * Miniature SO-8 Surface Mount Package - Saves Board Space
SINGLE TMOS POWER MOSFET 30 VOLTS RDS(on) = 11 mW
D
G S
MARKING DIAGRAM
8 SO-8 CASE 751 Style 12 1 XXX A L Y W = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week XXXXXX ALYW
(c) Semiconductor Components Industries, LLC, 2002
1
August, 2002 - Rev. 2
Publication Order Number: MMSF3350/D
MMSF3350
MAXIMUM RATINGS (TJ = 25C unless otherwise specified)
Parameter Drain-to-Source Voltage Drain-to-Gate Voltage Gate-to-Source Voltage Gate-to-Source Operating Voltage Operating and Storage Temperature Range Single Pulse Drain-to-Source Avalanche Energy - Starting TJ = 25C (VDD = 25 Vdc, VGS = 10 Vdc, L = 20 mH, IL(pk) = 10 A, VDS = 30 Vdc) Symbol VDSS VDGR VGS VGS TJ, Tstg EAS 1000 Value 30 30 20 16 -55 to 150 Unit Vdc Vdc Vdc Vdc C mJ
POWER RATINGS (TJ = 25C unless otherwise specified)
Parameter Drain Current - Continuous @ TA = 25C - Continuous @ TA = 100C - Single Pulse (tp 10 ms) Mounted on 1 inch square FR-4 or G10 board VGS = 10 Vdc t 10 seconds d Symbol ID ID IDM IS PD RqJA Value 13 9.2 50 3.6 2.7 22.2 46 Unit Adc Adc Adc Adc Watts mW/C C/W
Continuous Source Current (Diode Conduction) Total Power Dissipation @ TA = 25C Linear Derating Factor Thermal Resistance - Junction-to-Ambient
Parameter Drain Current - Continuous @ TA = 25C - Continuous @ TA = 100C - Single Pulse (tp 10 ms) Mounted on 1 inch square FR-4 or G10 board VGS = 10 Vdc Steady St t St d State
Symbol ID ID IDM IS PD RqJA
Value 9.4 6.7 50 2.0 1.5 11.8 85
Unit Adc Adc Adc Adc Watts mW/C C/W
Continuous Source Current (Diode Conduction) Total Power Dissipation @ TA = 25C Linear Derating Factor Thermal Resistance - Junction-to-Ambient
Parameter Drain Current - Continuous @ TA = 25C - Continuous @ TA = 100C - Single Pulse (tp 10 ms) Mounted on minimum recommended FR-4 or G10 board VGS = 10 Vdc t 10 seconds d
Symbol ID ID IDM IS PD RqJA
Value 10 7.4 50 2.4 1.8 14.3 70
Unit Adc Adc Adc Adc Watts mW/C C/W
Continuous Source Current (Diode Conduction) Total Power Dissipation @ TA = 25C Linear Derating Factor Thermal Resistance - Junction-to-Ambient
Parameter Drain Current - Continuous @ TA = 25C - Continuous @ TA = 100C - Single Pulse (tp 10 ms) Mounted on minimum recommended FR-4 or G10 board VGS = 10 Vdc Steady St t St d State
Symbol ID ID IDM IS PD RqJA
Value 7.4 5.2 50 1.2 0.9 7.1 140
Unit Adc Adc Adc Adc Watts mW/C C/W
Continuous Source Current (Diode Conduction) Total Power Dissipation @ TA = 25C Linear Derating Factor Thermal Resistance - Junction-to-Ambient
http://onsemi.com
2
MMSF3350
ELECTRICAL CHARACTERISTICS (TJ = 25C unless otherwise specified)
Characteristic OFF CHARACTERISTICS Drain-to-Source Breakdown Voltage (VGS = 0 Vdc, ID = 250 mAdc) Temperature Coefficient (Positive) Zero Gate Voltage Drain Current (VDS = 30 Vdc, VGS = 0 Vdc) (VDS = 30 Vdc, VGS = 0 Vdc, TJ = 125C) Gate-Body Leakage Current (VGS = 20 Vdc, VDS = 0 Vdc) ON CHARACTERISTICS(1) VGS(th) 1.0 - RDS(on) - - gFS 12 9.4 14.4 17 11 17 - Mhos 2.0 4.6 - - Vdc mV/C mW V(BR)DSS 30 - IDSS - - IGSS - 0.003 0.4 2.0 1.0 10 100 nAdc 33 23 - - Vdc mV/C mAdc Symbol Min Typ Max Unit
Gate Threshold Voltage (VDS = VGS, ID = 250 mAdc) Threshold Temperature Coefficient (Negative) Static Drain-to-Source On-Resistance (VGS = 10 Vdc, ID = 10 Adc) (VGS = 4.5 Vdc, ID = 5.0 Adc) Forward Transconductance (VDS = 15 Vdc, ID = 10 Adc) DYNAMIC CHARACTERISTICS Input Capacitance Output Capacitance Transfer Capacitance SWITCHING CHARACTERISTICS(2) (VDD = 25 Vdc, ID = 1.0 Adc, VGS = 4.5 Vdc, 4 5 Vdc RG = 6.0 W) (VDS = 24 Vdc, VGS = 0 Vdc, f = 1 0 MHz) 1.0
Ciss Coss Crss
- - -
1680 540 185
- - -
pF
Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Gate Charge
td(on) tr td(off) tf
- - - - - - - - - - - -
21 50 42 44 12 15 60 44 46 4.5 12.8 9.8
40 90 80 80 20 30 100 80 60 - - -
ns
(VDD = 25 Vdc, ID = 1.0 Adc, VGS = 10 Vdc, Vdc RG = 6.0 W)
td(on) tr td(off) tf
ns
(VDS = 15 Vdc, ID = 2.0 Adc, VGS = 10 Vdc)
QT Q1 Q2 Q3
nC
SOURCE-DRAIN DIODE CHARACTERISTICS Forward On-Voltage (1) (IS = 2.3 Adc, VGS = 0 Vdc) (IS = 2.3 Adc, VGS = 0 Vdc, TJ = 125C) (IS = 3.5 Adc, VGS = 0 Vdc, dIS/dt = 100 A/ms) VSD - - trr ta tb Reverse Recovery Stored Charge 1. Pulse Test: Pulse Width 300 ms, Duty Cycle 2%. 2. Switching characteristics are independent of operating junction temperatures. QRR - - - - 0.76 0.58 41 21 20 0.049 1.0 - - - - - mC ns Vdc
Reverse Recovery Time
http://onsemi.com
3
MMSF3350
TYPICAL ELECTRICAL CHARACTERISTICS
25 ID, DRAIN CURRENT (AMPS) 10 V 6.0 V 20 4.5 V 4.3 V 15 3.5 V 10 3.3 V 5 0 0 RDS(on) DRAIN-TO-SOURCE RESISTANCE (OHMS) , 0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0 RDS(on) DRAIN-TO-SOURCE RESISTANCE (OHMS) , VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) 3.1 V 2.9 V 2 0 2 2.5 3 3.5 4 VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) VGS = 3.7 V 4.1 V 3.9 V TJ = 25C 14 VDS . 10 V 12 10 8 TJ = 125C 6 4 -55C 25C
ID, DRAIN CURRENT (AMPS)
Figure 1. On-Region Characteristics
Figure 2. Transfer Characteristics
0.3 ID = 5.0 A TJ = 25C 0.2
0.020 0.018 0.016 0.014 0.012 0.010 0.008 0.006 0.004 0.002 0 0 5 10 20 15 ID, DRAIN CURRENT (AMPS) 25 10 V TJ = 25C VGS = 4.5 V
0.1
0 2 3 4 5 6 7 8 9 10 VGS, GATE-TO-SOURCE VOLTAGE (VOLTS)
Figure 3. On-Resistance versus Gate-To-Source Voltage
RDS(on) DRAIN-TO-SOURCE RESISTANCE , (NORMALIZED)
Figure 4. On-Resistance versus Drain Current and Gate Voltage
2.0 VGS = 10 V ID = 10 A 1.5
1000 VGS = 0 V IDSS LEAKAGE (nA) , 100 100C 10 TJ = 125C
1.0
0.5
1
25C
0 -50
0.1 -25 0 25 50 75 100 125 150 5 TJ, JUNCTION TEMPERATURE (C) 20 25 10 15 30 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
Figure 5. On-Resistance Variation with Temperature
Figure 6. Drain-To-Source Leakage Current versus Voltage
http://onsemi.com
4
MMSF3350
POWER MOSFET SWITCHING Switching behavior is most easily modeled and predicted by recognizing that the power MOSFET is charge controlled. The lengths of various switching intervals (Dt) are determined by how fast the FET input capacitance can be charged by current from the generator. The published capacitance data is difficult to use for calculating rise and fall because drain-gate capacitance varies greatly with applied voltage. Accordingly, gate charge data is used. In most cases, a satisfactory estimate of average input current (IG(AV)) can be made from a rudimentary analysis of the drive circuit so that t = Q/IG(AV) During the rise and fall time interval when switching a resistive load, VGS remains virtually constant at a level known as the plateau voltage, VSGP. Therefore, rise and fall times may be approximated by the following: tr = Q2 x RG/(VGG - VGSP) tf = Q2 x RG/VGSP where VGG = the gate drive voltage, which varies from zero to VGG RG = the gate drive resistance and Q2 and VGSP are read from the gate charge curve. During the turn-on and turn-off delay times, gate current is not constant. The simplest calculation uses appropriate values from the capacitance curves in a standard equation for voltage change in an RC network. The equations are: td(on) = RG Ciss In [VGG/(VGG - VGSP)] td(off) = RG Ciss In (VGG/VGSP)
4000 Ciss C, CAPACITANCE (pF) 3500 3000 2500 2000 1500 1000 500 0 -10 -5 VGS 0 5 VDS Crss 10 15 20 Coss VDS = 0 V Crss Ciss VGS = 0 V TJ = 25C
The capacitance (Ciss) is read from the capacitance curve at a voltage corresponding to the off-state condition when calculating td(on) and is read at a voltage corresponding to the on-state when calculating td(off). At high switching speeds, parasitic circuit elements complicate the analysis. The inductance of the MOSFET source lead, inside the package and in the circuit wiring which is common to both the drain and gate current paths, produces a voltage at the source which reduces the gate drive current. The voltage is determined by Ldi/dt, but since di/dt is a function of drain current, the mathematical solution is complex. The MOSFET output capacitance also complicates the mathematics. And finally, MOSFETs have finite internal gate resistance which effectively adds to the resistance of the driving source, but the internal resistance is difficult to measure and, consequently, is not specified. The resistive switching time variation versus gate resistance (Figure 9) shows how typical switching performance is affected by the parasitic circuit elements. If the parasitics were not present, the slope of the curves would maintain a value of unity regardless of the switching speed. The circuit used to obtain the data is constructed to minimize common inductance in the drain and gate circuit loops and is believed readily achievable with board mounted components. Most power electronic loads are inductive; the data in the figure is taken with a resistive load, which approximates an optimally snubbed inductive load. Power MOSFETs may be safely operated into an inductive load; however, snubbing reduces switching losses.
25
30
GATE-TO-SOURCE OR DRAIN-TO-SOURCE VOLTAGE (VOLTS)
Figure 7. Capacitance Variation
http://onsemi.com
5
MMSF3350
VGS GATE-TO-SOURCE VOLTAGE (VOLTS ,
12 QT 10 VGS 8 6 4 Q1 2 0 0 10 20 Q3 VDS 30 40 50 Q2 TJ = 25C ID = 2 A
18 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) 15 12 9 6 3 0
1000
t, TIME (ns)
100
10 1 10 RG, GATE RESISTANCE (OHMS) 100
Qg, TOTAL GATE CHARGE (nC)
Figure 8. Gate-To-Source and Drain-To-Source Voltage versus Total Charge
Figure 9. Resistive Switching Time Variation versus Gate Resistance
DRAIN-TO-SOURCE DIODE CHARACTERISTICS The switching characteristics of a MOSFET body diode are very important in systems using it as a freewheeling or commutating diode. Of particular interest are the reverse recovery characteristics which play a major role in determining switching losses, radiated noise, EMI and RFI. System switching losses are largely due to the nature of the body diode itself. The body diode is a minority carrier device, therefore it has a finite reverse recovery time, trr, due to the storage of minority carrier charge, QRR, as shown in the typical reverse recovery wave form of Figure 16. It is this stored charge that, when cleared from the diode, passes through a potential and defines an energy loss. Obviously, repeatedly forcing the diode through reverse recovery further increases switching losses. Therefore, one would like a diode with short trr and low QRR specifications to minimize these losses. The abruptness of diode reverse recovery effects the amount of radiated noise, voltage spikes, and current ringing. The mechanisms at work are finite irremovable circuit parasitic inductances and capacitances acted upon by high di/dts. The diode's negative di/dt during ta is directly controlled by the device clearing the stored charge. However, the positive di/dt during tb is an uncontrollable diode characteristic and is usually the culprit that induces current ringing. Therefore, when comparing diodes, the ratio of tb/ta serves as a good indicator of recovery abruptness and thus gives a comparative estimate of probable noise generated. A ratio of 1 is considered ideal and values less than 0.5 are considered snappy. Compared to Motorola standard cell density low voltage MOSFETs, high cell density MOSFET diodes are faster (shorter trr), have less stored charge and a softer reverse recovery characteristic. The softness advantage of the high cell density diode means they can be forced through reverse recovery at a higher di/dt than a standard cell MOSFET diode without increasing the current ringing or the noise generated. In addition, power dissipation incurred from switching the diode will be less due to the shorter recovery time and lower switching losses.
http://onsemi.com
6
MMSF3350
12 IS, SOURCE CURRENT (AMPS) 10 8 6 4 2 0 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.85 0.9 VSD, SOURCE-TO-DRAIN VOLTAGE (VOLTS) VGS = 0 V TJ = 25C
Figure 10. Diode Forward Voltage versus Current
di/dt = 300 A/ms I S, SOURCE CURRENT
Standard Cell Density trr High Cell Density trr ta tb
t, TIME
Figure 11. Reverse Recovery Time (trr)
SAFE OPERATING AREA The Forward Biased Safe Operating Area curves define the maximum simultaneous drain-to-source voltage and drain current that a transistor can handle safely when it is forward biased. Curves are based upon maximum peak junction temperature and a case temperature (TC) of 25C. Peak repetitive pulsed power limits are determined by using the thermal response data in conjunction with the procedures discussed in AN569, "Transient Thermal Resistance - General Data and Its Use." Switching between the off-state and the on-state may traverse any load line provided neither rated peak current (IDM) nor rated voltage (VDSS) is exceeded, and that the transition time (tr, tf) does not exceed 10 ms. In addition the total power averaged over a complete switching cycle must not exceed (TJ(MAX) - TC)/(RqJC). A power MOSFET designated E-FET can be safely used in switching circuits with unclamped inductive loads. For reliable operation, the stored energy from circuit inductance dissipated in the transistor while in avalanche must be less than the rated limit and must be adjusted for operating conditions differing from those specified. Although industry practice is to rate in terms of energy, avalanche energy capability is not a constant. The energy rating decreases non-linearly with an increase of peak current in avalanche and peak junction temperature.
http://onsemi.com
7
MMSF3350
EAS, SINGLE PULSE DRAIN-TO-SOURC AVALANCHE ENERGY (mJ) 100 10 ms 10 dc 1 ms 100 ms 1000 900 800 700 600 500 400 300 200 100 0 100 25 50 75 100 125 15 ID = 10 A
ID, DRAIN CURRENT (AMPS)
1
0.1 RDS(on) LIMIT THERMAL LIMIT PACKAGE LIMIT 0.1 1 10 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS)
0.01
TJ, STARTING JUNCTION TEMPERATURE (C)
Figure 12. Maximum Rated Forward Biased Safe Operating Area
Figure 13. Maximum Avalanche Energy versus Starting Junction Temperature
http://onsemi.com
8
MMSF3350
TYPICAL ELECTRICAL CHARACTERISTICS
100 0 DUTY CYCLE 10 0 10 D = 0.5 0.2 0.1 0.05 0.02 0.01 t2 SINGLE PULSE 0.1 1E-05 1E-04 1E-03 1E-02 1E-01 t, TIME (seconds) 1E+00 1E+01 1E+02 1E+0 RqJA(t) = r(t) RqJA D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 TJ(pk) - TA = P(pk) RqJA(t)
Rthja(t)EFFECTIVE TRANSIENT , THERMAL RESISTANCE
MOUNTED TO MINIMUM RECOMMENDED FOOTPRINT
1
Figure 14. Thermal Response - Various Duty Cycles
Rthja(t)EFFECTIVE TRANSIENT , THERMAL RESISTANCE
10,000 MIN PAD, jl MIN PAD, ja 1 INCH PAD, R C R C R ja C 0.0758 1.07 0.0707 0.417 0.0866 0.0142 1.12 16.9 0.456 3.10 0.558 0.106 276 6.61 1.59 11.0 4.95 46.7 5.64 289 60.8 1090 31.6 318 63.8 13,600 45.4 12,500 3.95 9,580 R1 CHIP JUNCTION C1 R2 C2 R3 C3 R4 C4 R5 C5 AMBIENT
1000
100
1 2 3 4 5
Rthja, MIN PAD Rthja, 1 INCH PAD
10
Rthjl, MIN PAD
1 1E-03 1E-02 1E-01 1E+00 t, TIME (seconds) 1E+01 1E+02 1E+
Figure 15. Thermal Response - Various Mounting/Measurement Conditions
80 MOUNTED ON 2, SQ. FR4 BOARD (1, SQ. 2 OZ. CU 0.06, THICK SINGLE SIDED). 60 POWER (W)
40 trr 20 tp 0.01 0.1 1 10 tb
0 t, TIME (seconds)
Figure 16. Single Pulse Power http://onsemi.com
9
Figure 17. Diode Reverse Recovery Waveform
MMSF3350
INFORMATION FOR USING THE SO-8 SURFACE MOUNT PACKAGE
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to ensure proper solder connection interface
between the board and the package. With the correct pad geometry, the packages will self-align when subjected to a solder reflow process.
0.060 1.52
0.275 7.0
0.155 4.0
0.024 0.6
0.050 1.270
SO-8 POWER DISSIPATION
The power dissipation of the SO-8 is a function of the input pad size. This can vary from the minimum pad size for soldering to the pad size given for maximum power dissipation. Power dissipation for a surface mount device is determined by TJ(max), the maximum rated junction temperature of the die, RqJA, the thermal resistance from the device junction to ambient; and the operating temperature, TA. Using the values provided on the data sheet for the SO-8 package, PD can be calculated as follows:
PD = TJ(max) - TA RqJA
the equation for an ambient temperature TA of 25C, one can calculate the power dissipation of the device which in this case is 2.7 Watts.
PD =
150C - 25C 46C/W
= 2.7 Watts
The values for the equation are found in the maximum ratings table on the data sheet. Substituting these values into
The 46C/W for the SO-8 package assumes the recommended footprint on a glass epoxy printed circuit board to achieve a power dissipation of 2.7 Watts using the footprint shown. Another alternative would be to use a ceramic substrate or an aluminum core board such as Thermal CladTM. Using board material such as Thermal Clad, the power dissipation can be doubled using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated temperature of the device. When the entire device is heated to a high temperature, failure to complete soldering within a short time could result in device failure. Therefore, the following items should always be observed in order to minimize the thermal stress to which the devices are subjected. * Always preheat the device. * The delta temperature between the preheat and soldering should be 100C or less.* * When preheating and soldering, the temperature of the leads and the case must not exceed the maximum temperature ratings as shown on the data sheet. When
* * *
*
using infrared heating with the reflow soldering method, the difference shall be a maximum of 10C. The soldering temperature and time shall not exceed 260C for more than 10 seconds. When shifting from preheating to soldering, the maximum temperature gradient shall be 5C or less. After soldering has been completed, the device should be allowed to cool naturally for at least three minutes. Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. Mechanical stress or shock should not be applied during cooling.
*Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device.
http://onsemi.com
10
MMSF3350
TYPICAL SOLDER HEATING PROFILE For any given circuit board, there will be a group of control settings that will give the desired heat pattern. The operator must set temperatures for several heating zones and a figure for belt speed. Taken together, these control settings make up a heating "profile" for that particular circuit board. On machines controlled by a computer, the computer remembers these profiles from one operating session to the next. Figure 1 shows a typical heating profile for use when soldering a surface mount device to a printed circuit board. This profile will vary among soldering systems, but it is a good starting point. Factors that can affect the profile include the type of soldering system in use, density and types of components on the board, type of solder used, and the type of board or substrate material being used. This profile shows temperature versus time. The line on the graph shows the actual temperature that might be experienced on the surface of a test board at or near a central solder joint. The two profiles are based on a high density and a low density board. The Vitronics SMD310 convection/infrared reflow soldering system was used to generate this profile. The type of solder used was 62/36/2 Tin Lead Silver with a melting point between 177-189C. When this type of furnace is used for solder reflow work, the circuit boards and solder joints tend to heat first. The components on the board are then heated by conduction. The circuit board, because it has a large surface area, absorbs the thermal energy more efficiently, then distributes this energy to the components. Because of this effect, the main body of a component may be up to 30 degrees cooler than the adjacent solder joints.
STEP 5 STEP 4 STEP 1 STEP 2 STEP 3 HEATING HEATING PREHEAT VENT HEATING ZONE 1 "SOAK" ZONES 2 & 5 ZONES 3 & 6 ZONES 4 & 7 "SPIKE" "SOAK" "RAMP" "RAMP" 200C 170C DESIRED CURVE FOR HIGH 160C MASS ASSEMBLIES 150C 150C SOLDER IS LIQUID FOR 40 TO 80 SECONDS 140C(DEPENDING ON MASS OF ASSEMBLY)
STEP 6 VENT
STEP 7 COOLING
205 TO 219C PEAK AT SOLDER JOINT
100C 100C
DESIRED CURVE FOR LOW MASS ASSEMBLIES 50C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
Figure 18. Typical Solder Heating Profile
DEVICE MARKING
S3350
ORDERING INFORMATION
Device MMSF3350R2 Reel Size 13 Tape Width 12 mm embossed tape Quantity 2500 units
http://onsemi.com
11
MMSF3350
PACKAGE DIMENSIONS
SOIC-8 NB CASE 751-07 ISSUE AA
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDAARD IS 751-07 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 SOURCE SOURCE SOURCE GATE DRAIN DRAIN DRAIN DRAIN INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244
-X- A
8 5
B
1 4
S
0.25 (0.010)
M
Y
M
-Y- G C -Z- H D 0.25 (0.010)
M SEATING PLANE
K
N
X 45 _
0.10 (0.004)
M
J
ZY
S
X
S
DIM A B C D G H J K M N S
STYLE 12: PIN 1. 2. 3. 4. 5. 6. 7. 8.
WaveFET is a trademarks of Semiconductor Components Industries, LLC (SCILLC). HDTMOS is a registered trademarks of Semiconductor Components Industries, LLC (SCILLC). Thermal Clad is a registered trademark of the Bergquist Company.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
12
MMSF3350/D

▲Up To Search▲

Price & Availability of MMSF3350-D

	To Download MMSF3350-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .